====== DIR-300 rev. B1 ======
Скачиваем прошивку FIXME
http://downloads.openwrt.org/barrier_breaker/14.07/ramips/rt305x/openwrt-ramips-rt305x-dir-300-b1-squashfs-factory.bin
minicom -b57600
Welcome to minicom 2.6.1
OPTIONS: I18n
Compiled on Feb 11 2012, 18:12:55.
Port /dev/ttyS0
Press CTRL-A Z for help on special keys
U-Boot 1.1.3 (Jan 13 2009 - 17:40:14) (Alpha) - SVN revision : 105
Model: WRGN23
Board: RT2880 DRAM: 32 MB
twe0 set to
toe0 set to
============================================
Ralink UBoot Version: 3.1 Alpha
--------------------------------------------
ASIC 3052_MP2 (MAC to GigaMAC Mode)
DRAM COMPONENT: 256Mbits
DRAM BUS: 16BIT
Total memory: 32Mbytes
Date:Jan 13 2009 Time:17:40:14
============================================
icache: sets:128, ways:4, linesz:32 ,total:16384
dcache: sets:128, ways:4, linesz:32 ,total:16384
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
0 seconds ...
Eth0 (10/100-M) : ethaddr = (1c:af:f7:14:6e:3a) 1C AF F7 14 6E 3A
3: System Boot system code via Flash.
## Powering down port 0 ~ 3.
## Booting image at bf050000 ...
Bad Magic Number,48445230
Entering HTTP server.
Mac to giga Mac mode
Using Eth0 (10/100-M) device
Start HTTP server on port 80, 192.168.0.1
Running ...
Открываем в браузере http://192.168.0.1
Загружаем прошивку. Видим сообщение в браузере:
IMAGE UPLOADED SUCCESSFULLY
3407972 bytes uploaded.
The WEB server is shuting down and the firmware updating will start immediately. Please DO NOT POWER OFF the device. And please wait for seconds...
При этом в консоли minicom наблюдаем следующее:
mpfd_decode: UPLOADED, upsize = 3407972
IMGHDR========================================
signature : wrgn23_dlwbr_dir300b
magic : 20040220
==============================================
IMGBLOCK======================================
maigc : 20040220
size : 3407876
offset : 0
devname : /dev/mtdblock/2
digest : F341A39E5A728B773CB3A4A6A0ED8610
==============================================
Erase linux block (0xbf050000 ~ 0xbf39ffff)
*******************Erased 53 sectors
Copy linux image [3407876 bytes] to Flash [0xBF050000] ...
Copy 3407876 byte to Flash ...done
## Booting image at bf050000 ...
Image Name: MIPS OpenWrt Linux-3.10.49
Created: 2014-10-01 14:33:48 UTC
System Control Status = 0x03400000
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1054546 Bytes = 1 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/4
[ 0.000000] SoC Type: Ralink RT3350 id:1 rev:2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[ 0.000000] MIPS: machine is D-Link DIR-300 B1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bys
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa8
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jff2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00066ad0
[ 0.000000] Readback ErrCtl register=00066ad0
[ 0.000000] Memory: 29160k/32768k available (2284k kernel code, 3608k reserv)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 320MHz
[ 0.000000] Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] pinctrl core: initialized pinctrl subsystem
[ 0.100000] NET: Registered protocol family 16
[ 0.160000] bio: create slab at 0
[ 0.170000] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.180000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.200000] Switching to clocksource MIPS
[ 0.210000] NET: Registered protocol family 2
[ 0.220000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.230000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.240000] TCP: Hash tables configured (established 512 bind 512)
[ 0.260000] TCP: reno registered
[ 0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.270000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.290000] NET: Registered protocol family 1
[ 0.300000] rt-timer 10000100.timer: maximum frequncy is 6510Hz
[ 0.360000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.380000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORI.
[ 0.400000] msgmni has been set to 56
[ 0.410000] io scheduler noop registered
[ 0.410000] io scheduler deadline registered (default)
[ 0.430000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.460000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 1655A
[ 0.480000] console [ttyS0] enabled, bootconsole disabled
[ 0.480000] console [ttyS0] enabled, bootconsole disabled
[ 0.510000] 1f000000.cfi: Found 1 x16 devices at 0x0 in 16-bit bank. Manufac8
[ 0.530000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.540000] Amd/Fujitsu Extended Query version 1.1.
[ 0.550000] number of CFI chips: 1
[ 0.560000] 4 ofpart partitions found on MTD device 1f000000.cfi
[ 0.570000] Creating 4 MTD partitions on "1f000000.cfi":
[ 0.580000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.590000] 0x000000030000-0x000000040000 : "devdata"
[ 0.610000] 0x000000040000-0x000000050000 : "devconf"
[ 0.620000] 0x000000050000-0x000000400000 : "firmware"
[ 0.640000] 0x000000151792-0x000000400000 : "rootfs"
[ 0.650000] mtd: partition "rootfs" must either start or end on erase block y
[ 0.680000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.690000] mtd: partition "rootfs_data" created automatically, ofs=0x3700000
[ 0.710000] 0x000000370000-0x000000400000 : "rootfs_data"
[ 0.740000] eth0: done loading
[ 0.750000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.760000] TCP: cubic registered
[ 0.770000] NET: Registered protocol family 17
[ 0.780000] Bridge firewalling registered
[ 0.790000] 8021q: 802.1Q VLAN Support v1.8
[ 0.810000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.830000] Freeing unused kernel memory: 212K (802cb000 - 80300000)
procd: Console is alive
procd: - watchdog -
[ 3.840000] usbcore: registered new interface driver usbfs
[ 3.850000] usbcore: registered new interface driver hub
[ 3.860000] usbcore: registered new device driver usb
[ 3.890000] dwc_otg: version 2.72a 24-JUN-2008
[ 3.900000] leds-gpio gpio-leds.4: pins are not configured from the driver
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
jffs2 is not ready - marker found
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 11.310000] NET: Registered protocol family 10
[ 11.340000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)
[ 11.370000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.400000] Loading modules backported from Linux version master-2014-05-22-a
[ 11.420000] Backport generated by backports.git backports-20140320-37-g5c33d0
[ 11.440000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.540000] xt_time: kernel timezone is -0000
[ 11.600000] cfg80211: Calling CRDA to update world regulatory domain
[ 11.670000] cfg80211: World regulatory domain updated:
[ 11.680000] cfg80211: DFS Master region: unset
[ 11.680000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_ga)
[ 11.700000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 )
[ 11.720000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 )
[ 11.740000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 )
[ 11.750000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000)
[ 11.770000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000)
[ 11.790000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000)
[ 11.800000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 )
[ 11.820000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0)
[ 11.900000] PPP generic driver version 2.4.2
[ 11.910000] NET: Registered protocol family 24
[ 11.970000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 d
[ 11.990000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[ 25.230000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 25.340000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 25.350000] jffs2_build_filesystem(): erasing all blocks after the end markee
[ 30.120000] device eth0 entered promiscuous mode
[ 30.140000] br-lan: port 1(eth0.1) entered forwarding state
[ 30.150000] br-lan: port 1(eth0.1) entered forwarding state
done.
[ 30.180000] jffs2: notice: (862) jffs2_build_xattr_subsystem: complete build.
[ 32.150000] br-lan: port 1(eth0.1) entered forwarding state
procd: - init complete -
BusyBox v1.22.1 (2014-09-21 10:15:39 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (14.07, r42625)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/#
====== Ссылки ======
http://wiki.openwrt.org/toh/d-link/dir-300revb
http://infodepot.wikia.com/wiki/D-Link_DIR-300_vB1